![vsx-1022-k stby assy board view vsx-1022-k stby assy board view](https://i.ebayimg.com/images/g/W-0AAOSwvtVg-aty/s-l640.png)
![vsx-1022-k stby assy board view vsx-1022-k stby assy board view](https://elektrotanya.com/PREVIEWS/63463243/23432455/pioneer/pioneer_sx-8_arp0430.pdf_1.png)
#VSX 1022 K STBY ASSY BOARD VIEW CODE#
If a new plug is to be fitted, please observe the wiring code as shown below. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket. If the fitted moulded plug is unsuitable for your socket outlet, then the fuse shall be removed and the plug cut off and disposed of safely. A replacement fuse cover can be obtained from your local dealer. If you lose the fuse cover the plug must not be used until a replacement cover is obtained. If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. Check for the ASTA mark or the BSI mark on the body of the fuse. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 10 amps and that it is approved by ASTA or BSI to BS1362. IMPORTANT: THE MOULDED PLUG This appliance is supplied with a moulded three pin mains plug for your safety and convenience. D8-10-3a_ Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel. To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded cables and connectors for connections. D8-10-2_ CAUTION: This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other equipment. D _ Information to User Alteration or modifications carried out without appropriate authorization may invalidate the user s right to operate the equipment. Consult the dealer or an experienced radio/tv technician for help. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Increase the separation between the equipment and receiver. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. However, there is no guarantee that interference will not occur in a particular installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. These limits are designed to provide reasonable protection against harmful interference in a residential installation. D _-A NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. REFER SERVICG TO QUALIFIED SERVICE PERSONNEL. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). Also, Pioneer has an extensive repair network and are very helpful if you contact them.1 AUDIO/VIDEO MULTI-CHANNEL RECEIVER VSX-416-S/-K VSX-516-S/-K Operating InstructionsĢ IMPORTANT The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. Also, I wouldn't recommend opening up your receiver in the future as it voids the warranty in most cases. Otherwise, it means your power supply is probably fried. If you try and turn the receiver on and nothing happens but the red light is still visible then this method will work. Note: I think the front standby light needs to at least be visible when the receiver is plugged in for this to work. My receiver is the VSX-D812-K, but they are pretty similar and it should work. I sure hope this helps you before you have to go through the trouble I did. All they did was press and hold ENTER and ADVANCED SURROUND on the front panel for 2 seconds. It sat at one repair shop for over a month and they couldn't fix it and then I contacted Pioneer and I happened to be a few miles from their best repair shop.
#VSX 1022 K STBY ASSY BOARD VIEW MANUAL#
I tried using the reset method in the manual but it didn't work and spent a few months looking for a place to fix it. I had the exact same thing happen to me several months back.